SOYAL TECHNOLOGY CO., LTD

Standard Firmware
◎Floor and alias information needs to be downloaded to the card readers under RS485.
◎701ClientSQL 10V5 significantly improves the RS485 card recognition speed.

◎Floor and alias information only needs to be downloaded to the AR-716-E16 and doesn't require separate downloads to the 16 card readers under RS485.
◎Supports increasing the floor control capacity of H-series controllers from the original 32 floors to 64 floors.
◎Supports increasing the user capacity control of H-series controllers from the original 1024 users to 16,000 users.
◎701ClientSQL 10V5 significantly improves the RS485 card recognition speed.

5 Card N Space (Specific Application: Shared Parking Space, CH1 wire to access controller CH2 wire to LED display board)

Standard Firmware

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware
Release lock in high temperature and temperature can be 35.5 °C

Customized Firmware
Release lock in high temperature but temperature must exceed 35.5 °C

Customized Firmware
Set specific user floor access or mailbox number in User Card Edit's Alias field (first three digit number, example: '001' for 1st mailbox access)

Customized Firmware
Mifare is in reverse order (applied to the WG reader with reverse UID order)

Customized Firmware
Trigger Alarm if invalid card or Anti-passback error

Customized Firmware
Mifare & WG Input are in reverse order (applicable for system that use reverse UID order, if this is the case please enter the original card ID)

Customized Firmware
Release of elevator floor control in case of fire (Requires use with AR-727-CM-IO-0804M).

Customized Firmware
External Display Board 8 Secs. AUTO_RENEW_LED

Customized Firmware
Body Temperature Access Mode

Standard Firmware
Whether wearing face mask or not, the face can be recognized to access; but the security level should be set to [ Level Low] if detecting face mask

Customized Firmware
Only wearing face mask is allowed to access and trigger alert if the recognizing face does not wear a mask

Standard Firmware

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware : DoorSensor

Firmware Updating Setting Step

Standard Firmware

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware :
When swiping the card, only elevator floor access is trigger, relay remain untriggered.
Control the power of elevator relay with normal close contact of door relay. That way, under fire alarm event when access control releasing the door lock, at the same time will also release elevator control

Customized Firmware:
reversed hex

Customized Firmware
SOYAL DESFire Only

Customized Firmware:
Dual door interlock

Standard Firmware

Customized Firmware
Enable card sensing only when the door position detection is grounded.

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware
When swiping the card, only elevator floor access is trigger, relay remain untriggered.
Control the power of elevator relay with normal close contact of door relay. That way, under fire alarm event when access control releasing the door lock, at the same time will also release elevator control

Customized Firmware
reversed hex

Customized Firmware
SOYAL DESFire Only

Customized Firmware
Dual door interlock

Standard Firmware

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware
◎Swipe valid card does not open door
◎Controller set as "Enable Any Tags to release door open", then combined with One Way(8031) and Two Way Hosting (8033) function. Suitable for back end judgement of access control or visitor membership, and can be monitored globally at the same time.

Customized Firmware : DoorSensor

Customized Firmware : reversed hex

Customized Firmware
Use 3 number on Alias Field for Floor Number

The LED does not light up during standby

The green LED blink during standby mode

The green LED is solid during standby

Standard Firmware

Customized Firmware
Keypad can output under WG mode, support card flashing and PIN access.

Customized Firmware
Release lock in high temperature and temperature can be 35.5 °C

Customized Firmware
Release lock in high temperature but temperature must exceed 35.5 °C

After firmware update must send Command 81 via Commview

Standard Firmware
◎ Capable of logic programming with calendar, time, holiday, counters, timers, DI/DO functions.
◎Supports a web-based editing interface for 64 logic expressions.

Customized Firmware :
When the PLC's DI changes, it will proactively send a message to the Remote IP of CH2, and CH2 needs to be set to TCP Client Mode.

Customized Firmware : When DI changes, it will proactively send a message to the Remote IP of CH2, and CH2 needs to be set to TCP Client Mode.

Standard Firmware

Customized Firmware : Modbus are in reverse order

Support Fire Alarm Event UDP Mode

Expandable Daisy-Chained Ethernet I/O over 256 DI and 256 DO includes Active Push Communciation DI Event via TCP function

Active Push Communciation DI Event via TCP

Expandable Daisy-Chained Ethernet I/O over 256 DI and 256 DO that is compatible with standard Modbus and SCADA graphic control

Customized Firmware
When Local DI status change from on/off, the corresponding Remote DO status on/off will be changed at the same time.
(Local AR-727-CM-IO or AR-401-IO-0808R-U2 setting of 'Remote IP' must be specified)

Customized Firmware : Local DI Trigger Local DO (Level Type)

Customized Firmware : Local DI Trigger Local DO (Edge Type)

Standard Firmware
Suitable for low speed (every 2ms low pulse 0.5ms) Wiegand data transmission device

Support Fire Alarm Event UDP Mode

Expandable Daisy-Chained Ethernet I/O over 256 DI and 256 DO includes Active Push Communciation DI Event via TCP function

Active Push Communciation DI Event via TCP

Customized Firmware : Local DI Trigger Local DO (Edge Type)

Customized Firmware : Local DI Trigger Local DO (Level Type)

Customized Firmware : When DI changes, it will proactively send a message to the Remote IP of CH2, and CH2 needs to be set to TCP Client Mode.

Standard Firmware
◎Support Graphic Animation feature for elevator control to manually control access to each floor
◎Support AR-727-CM MODBUS RCU

Standard Firmware